Technical Data
Base	Polymer modified pozzolanic cementitious
Color	Tan
Mixing Ratio	50 lb Bag / 1 gal water + ½ gal P-100 Primer Refer to Mixing Instructions
Working Time	10-15 minutes at 72°F Working time will vary with ambient conditions, water ratio and temperature.
Set Time	Initial Set - 100 minutes Final Set - 2 to 4 hours Most flooring can be installed 16 to 24 hours after F-10 is poured.
Comprehensive Strength	24 hour - 1040 psi 7 day - 2900 psi 28 day - 5100 psi 28 day - 5200 psi (with admixture) ASTM C-109
Absorption Rate	24 hour - 5.3% ASTM C-67
Flexural Strength	24 hour - 910 psi ASTM C-348
Coverage	46-50 sq. ft. per 50 lb of powder with 1/8" thickness.
Packaging	50 lb. bags
Shelf Life	6 months if stored in a cool, dry location. Keep bags tightly sealed when not in use.
Note	Contains no asbestos or portland cement. Made with post-industrial recycled fly ash

A FritzGREEN Product
Products designed with the environment in mind.
For more information, click here.

F-1000 is a polymer modified pozzolanic cementitious self-leveling underlayment for use with new and existing floors and decks, interior or exterior. Packaged in dry powder form, the product requires the addition of clean water over properly primed substrates.

• A remarkable balance of low water demand and superb workability that dramatically decreases water permeability.
• Pumpable, self leveling and open to light traffic in two to four hours.
• Effective from feather edge to 2" thickness on concrete, masonry, terrazzo and ceramic subfloors.
• Effective from feather edge to 2" thickness on wood subfloors.

Limitations

Apply only at temperatures between 40°F and 95°F. Do not use over press wood, chipboard, masonite or similar unstable materials.

Surface Preparations

Substrates must be solid, clean and free from dust, oil, grease, paint, wax sealers or any deleterious substance which may act as a bond barrier. Priming using P-100 primer is recommended on all surfaces. Prime according to instructions.

APPLICATION
for Concrete, Masonry, Terrazzo & Ceramic Tile Sub-Floors

These sub floors must be primed with Fritz P-100 Acrylic Primer diluted one to one. Apply the diluted primer at a coverage rate of 250-275 sq. ft. per gallon. Allow to dry one to two hours, but no more than 12 hours.

Mixing: The entire bag of F-1000 should be mixed in a clean mixing container. While mixing by hand, add water until a desired trowelable, lump free consistency is achieved. The recommended mixing ratio is 3½ parts powder to 1 part water by volume. DO NOT OVER-WATER!

APPLICATION
for Wood Sub-Floors

Use Fritz P-100 Acrylic Primer. Allow to dry one hour, but no more than 12 hours. After the primer is dry, staple or nail a thin diamond metal lathe mesh to floor.

Mixing: Mix 50 lbs. Fritz F-1000 Underlayment with one gallon water plus ½ gallon P-100 Primer. Spread Fritz Underlayment on to the floor surface as quickly as possible after mixing. Smoothing characteristics are retained during the first fifteen to twenty minutes. Spread the material with a steel straight edge or flat edge hand trowel or rubber squeegee. No surface troweling is necessary, as the material is selfleveling. For best results, spread in a continuous flow. Allow to set. Underlayment can be walked on in three to four hours after installation, and covered with flooring materials 12 to 18 hours later. Protect from traffic, dirt and dust until final floor covering material is installed.

Some documents require Adobe Reader
If you've not yet installed Adobe Reader on your computer, click here to download and install it.