-
-A polymer modified, pozzolan based cementitious type material which requires the addition of clean water to produce a fast setting, dimensionally stable, high strength underlayment. Poz-Patch 100 is a trowelable product that can be applied from featheredge to 1½" thickness in one application. Poz-Patch 100 can be used on, below and above grade as an exterior or interior underlayment for carpeting, vinyl, ceramic tile, asphalt, wood flooring and other compatible coverings.
  • Super Fast Installation
  • High Compressive Strength
  • 1½" Featheredge
-
click for more info

Limitations
Apply only at temperatures between 50°F and 95°F. Do not use over unstable materials. DO NOT USE ON WOOD SUBFLOOR.

Surface Preparations
All subfloors must be sound, solid, dry, clean and free from dust, oil, grease, paint, wax, curing agents, sealers, release agents, or any deleterious substance which may act as a bond barrier.

Mixing
Electric Drill: Pour 2 quarts of clean water in a clean mixing container and mix while adding entire contents of this 17 ½ lbs. bag of Poz-Patch 100. Mix thoroughly with a heavy duty drill and mixer blade for 1 to 2 minutes to achieve a smooth, trowelable, homogeneous consistency. Do not over mix or entrap air in the material.

Hand Mixing: If less than a full bag is needed, place the desired amount of Poz-Patch 100 in a clean mixing container. While mixing by hand, add water until a desired trowelable, lump free consistency is achieved. The recommended mixing ratio is 3½ parts powder to 1 part water by volume. DO NOT OVER-WATER! Poz-Patch 100 is not to be used as a self-leveling underlayment.

CAUTION
Mix only the amount of material that can be applied in 10 to 15 minutes. After mixing with water, material normally hardens in 45 to 60 minutes. Do not re-temper. Any variation in the recommended quantity of water will affect the working and performance characteristics of the mix. It is recommended that a test be made to determine the suitability of this product for its intended use.

Application
Area to be patched must be swept clean and primed with P-100. Allow primer to dry and pour Poz-Patch 100 into intended area using “Bond Coat Techniques”. Smooth with a steel trowel or smoothing blade. DO NOT OVERTROWEL. Poz-Patch 100 can walked on after 60 minutes. Flooring can be installed in 1 to 2 hours if latex-based adhesives are used. Flooring requiring special adhesives can be installed 12 hours after application. A bag covers approximately 18 square feet at 1/8” thickness.

CAUTION
This is a cementitious type product that could be irritating to the eyes and skin. Rubber gloves are recommended. Avoid contact with eyes or prolonged contact with skin. In case of contact with skin, flush the thoroughly with water. In case of contact with eyes, flush with water, then seek prompt medical attention.


Documents for POZ PATCH-100


-
-
-
Technical Data
Base Polymer modified pozzolanic cementitious type
Color Tan
Mixing Ratio 2 quarts water per 17½ lb bag
3.5 parts powder to 1 part water
Refer to Mixing Instructions
Working Time 10-15 minutes at 72º F.
Working time will vary with ambient conditions, water ratio and temperature.
Set Time Initial Set - 45 minutes
Final Set - 60 minutes
ASTM C-191
Bond Strength 7 day - 660 psi (with P-100 primer)
Comprehensive Strength 4 hour - 1050 psi
24 hour - 1600 psi
7 day - 2800 psi
28 day - 4000 psi
ASTM C-109
Absorption Rate 24 hours - 5.3%
ASTM C-67
Flexural Strength 24 hour - 820 psi
28 day - 1010 psi
ASTM C-348
Coverage 18 sq. feet at 1/8" thickness
Packaging 17½ lb bag
Shelf Life One year if stored in a cool, dry area. Keep bags tightly sealed when not in use.
Note Contains no asbestos or portland cement. Made with post-industrial recycled fly ash
-  

Fritz Industries • 500 Sam Houston Road • Mesquite, Texas • 75149
Phone:(972)285-5471 • Toll Free:(800)955-1323 • Fax:(972)270-0179
e-mail:tilesales@fritzind.com